Nighthawk: Created page with "Below is a console/terminal log of a new hard drive being installed, replacing a failed drive, and being added back to the raid mirror. BOOTMGR[4]> sysinfo CPU 0: 2660 MHz..."

2013-02-25T22:09:19Z

Created page with "Below is a console/terminal log of a new hard drive being installed, replacing a failed drive, and being added back to the raid mirror. BOOTMGR[4]> sysinfo CPU 0: 2660 MHz..."

New page

Below is a console/terminal log of a new hard drive being installed, replacing a failed drive, and being added back to the raid mirror.

BOOTMGR[4]> sysinfo

CPU 0: 2660 MHz Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Memory: 2663497728 (2048M bytes)
Disk Devices:
IO port 0x1f0 adc0: unit 0 (ad0): <STEC M2+ CF 9.0.2>
128MB (250880 sectors), 980 cyls, 8 heads, 32 S/T
SCSI-DISK-A (da0): <ATA FUJITSU MHY2080B 010C>
80026MB (156301488 sectors), 9729 cyls, 255 heads, 63 S/T, 512 B/S
SCSI-DISK-B (da1): <ATA FUJITSU MHY2080B 010C>
80026MB (156301488 sectors), 9729 cyls, 255 heads, 63 S/T, 512 B/S
Network Interfaces:
eth-s4p1: flags=130<BROADCAST,MULTICAST,PRESENT>
ether 00:a0:8e:c0:c2:f4 half duplex
eth-s4p2: flags=130<BROADCAST,MULTICAST,PRESENT>
ether 00:a0:8e:c0:c2:f5 half duplex
eth-s4p3: flags=130<BROADCAST,MULTICAST,PRESENT>
ether 00:a0:8e:c0:c2:f6 half duplex
eth-s4p4: flags=130<BROADCAST,MULTICAST,PRESENT>
ether 00:a0:8e:c0:c2:f7 half duplex
loop0: flags=10b<UP,LINK,LOOPBACK,PRESENT>
tun0: flags=107<UP,LINK,POINTOPOINT,PRESENT>
BOOTMGR[5]> raid

========================================================
IPSO LSI Logic Configuration Utility
version : Version 0.5, June 8, 2007
========================================================
Adapter Type ............. 3 (SAS Adapter)
PCI Device ID ............ 0x0056
Hardware Revision ID ..... 0x0004
Devices in Volume ........ 0
FW Version ............... (01.18.00.00) decimal
MPI Version of FW ........ MPI Version 1.5.13.0
========================================================
1) Raid Options Sub-Menu
2) Firmware operations
q) EXIT
========================================================

Choose an option: 1

=================== RAID MENU ==========================
1) Show volume(s)
2) Show physical disk(s)
3) Get Volume Status

Options below available from boot manager
-----------------------------------------
10) Disable volume
11) Enable volume
12) Deactivate volume
13) Activate volume
30) Create RAID Volume
31) Delete RAID Volume
q) Main Menu
========================================================

Choose an option: 30
B___T___L Type Serial Product Rev Blocks Disk MB
1. 0 0 0 Disk K449T8825xxx FUJITSU MHY2080B 010C 156301488 76319
2. 0 1 0 Disk K449T8625yyy FUJITSU MHY2080B 010C 156301488 76319

To create a volume, select two or more of the available targets
The first selection will be Migrated as MASTER, keeping the data

Select the primary drive : [1-2 or RETURN to quit] 1
Select a secondary drive : [1-2 or RETURN to quit] 2

2 physical disks were created

Setting volume type: [0=Mirroring]
Setting volume size: 76158 MB
Enabled write caching by default.

Volume was created

Changes made, doing a camcontrol rescan
Re-scan of bus 0 was successful
Re-scan of bus 0 was successful
Waiting 5 seconds for SCSI devices to settle ...... done

=================== RAID MENU ==========================
1) Show volume(s)
2) Show physical disk(s)
3) Get Volume Status

Options below available from boot manager
-----------------------------------------
10) Disable volume
11) Enable volume
12) Deactivate volume
13) Activate volume
30) Create RAID Volume
31) Delete RAID Volume
q) Main Menu
========================================================

Choose an option: 1
------------------ Show Volumes ------------------------
1 volume is active, 2 physical disks are active

Volume 0 is Bus 0 Target 0, Type IM (Integrated Mirroring)
Volume State: degraded, enabled, resync in progress
Volume Settings: write caching enabled, auto configure
Volume Size 76158 MB, Stripe Size 0 KB, 2 Members
Primary is PhysDisk 0 (Bus 0 Target 4)
Secondary is PhysDisk 1 (Bus 0 Target 1)

=================== RAID MENU ==========================
1) Show volume(s)
2) Show physical disk(s)
3) Get Volume Status

Options below available from boot manager
-----------------------------------------
10) Disable volume
11) Enable volume
12) Deactivate volume
13) Activate volume
30) Create RAID Volume
31) Delete RAID Volume
q) Main Menu
========================================================

Choose an option: q
========================================================
1) Raid Options Sub-Menu
2) Firmware operations
q) EXIT
========================================================

Choose an option: q
Re-scan of bus 0 was successful
Re-scan of bus 0 was successful
Waiting 5 seconds for SCSI devices to settle ..
Type 'boot <enter>' to continue boot process ..

BOOTMGR[13]> sysinfo
CPU 0: 2660 MHz Intel(R) Xeon(R) CPU E5430 @ 2.66GHz
Memory: 2663497728 (2048M bytes)
Disk Devices:
IO port 0x1f0 adc0: unit 0 (ad0): <STEC M2+ CF 9.0.2>
128MB (250880 sectors), 980 cyls, 8 heads, 32 S/T
DISK-A-B Volume (da0): <LSILOGIC Logical Volume 3000>
79857MB (155971584 sectors), 9708 cyls, 255 heads, 63 S/T, 512 B/S
Network Interfaces:
eth-s4p1: flags=130<BROADCAST,MULTICAST,PRESENT>
ether 00:a0:8e:c0:c2:f4 half duplex
eth-s4p2: flags=130<BROADCAST,MULTICAST,PRESENT>
ether 00:a0:8e:c0:c2:f5 half duplex
eth-s4p3: flags=130<BROADCAST,MULTICAST,PRESENT>
ether 00:a0:8e:c0:c2:f6 half duplex
eth-s4p4: flags=130<BROADCAST,MULTICAST,PRESENT>
ether 00:a0:8e:c0:c2:f7 half duplex
loop0: flags=10b<UP,LINK,LOOPBACK,PRESENT>
tun0: flags=107<UP,LINK,POINTOPOINT,PRESENT>

[[category:nokia]]

Adding drives to nokia firewall - Revision history

Nighthawk: Created page with "Below is a console/terminal log of a new hard drive being installed, replacing a failed drive, and being added back to the raid mirror. BOOTMGR[4]> sysinfo CPU 0: 2660 MHz..."